PB Blockup / Platforms Technician TDC

Job Summary

Required Qualifications

• •High school diploma or general education degree (GED)
• •One to three months related experience and/or training
• •Equivalent combination of education and experience
• •Ability to read and interpret documents such as safety rules, operating and maintenance instructions, and procedure manuals
• •Ability to write routine reports and correspondence
• •Ability to speak effectively before groups of customers or employees of organization
• •Ability to add, subtract, multiply, and divide in all units of measure, using whole numbers, common fractions, and decimals
• •Ability to compute rate, ratio, and percent
• •Ability to draw and interpret bar graphs
• •Ability to solve practical problems and deal with a variety of concrete variables in situations where only limited standardization exists
• •Ability to interpret a variety of instructions furnished in written, oral, diagram, or schedule form
• •Must be able to understand and execute top quality
• •Must be able to pass the strength/stress test
• •Must be able to pass drug/alcohol screening
• •Job requires standing and working in and around boats/molds throughout the entire day
• •Must work efficiently and in the safest manner possible
• •Must follow all safety regulations at all time
• •Safety glasses required while in production areas
• •Other PPE may be required based on specific projects
• •Typical 10 hour work day
• •Typical 4- or 5-day work week schedule based upon schedule
• •Overtime is occasional to frequent based on a number of factors
• •Required to work indoors and outdoors, year round and in all weather conditions
• •May be required to work during production shutdowns or other 'off-schedule' periods to conduct special activities
• •Must be able to lift 50 lbs
• •Must be able to frequently lift 15 lbs
• •Must be able to occasionally lift 30 lbs
• •Must be able to bend at waist
• •Must be able to squat
• •Must be able to climb ladders and stairs
• •Must be able to kneel on ground
• •Must be able to reach above shoulder
• •Must be able to sit for 2 hours
• •Must be able to stand for 5 hours
• •Must be able to walk for 3 hours
• •Must be able to drive for 0 hours
• •Must be able to perform simple grasping with right hand
• •Must be able to perform simple grasping with left hand
• •Must be able to perform pushing/pulling with right hand
• •Must be able to perform pushing/pulling with left hand
• •Must be able to perform fine manipulation with right hand
• •Must be able to perform fine manipulation with left hand
• •Must be able to perform right foot activities occasionally
• •Must be able to perform left foot activities occasionally
• •Must be able to work in ambient cold temperatures for short periods in winter months
• •Must be able to work in ambient heat temperatures in summer months
• •Must be able to work in a very dusty environment
• •Must be able to handle airborne particulates from cutting, drilling, grinding
• •Must be able to handle exposure to extremely sharp tooling used for cutting fiberglass
• •Must balance team and individual responsibilities
• •Must exhibit objectivity and openness to others' views
• •Must give and welcome feedback
• •Must contribute to building a positive team spirit
• •Must put success of team above own interests
• •Must support everyone's efforts to succeed
• •Must measure self against standard of excellence
• •Must demonstrate accuracy and thoroughness
• •Must apply feedback to improve performance
• •Must monitor own work to ensure quality
• •Must be consistently at work and on time
• •Must take responsibility for own actions
• •Must ensure associates comply with Pursuits policies, codes, and procedures
• •Must support plans to achieve key metrics for their department, i.e. safety, turnover, and supply spending
• •Must understand environmental compliance as it relates to material used in their area: chemical handling, usage, labeling, storage, and disposal
• •Must support continuous improvement utilizing Safety system, Kaizen, CAR system, and other problem-solving techniques
• •Must be responsible for the proper maintenance of all equipment used in their area
• •Must drive workplace organization using the 5S methodology
• •Must identify problems (i.e. material shortages, employee relations issues, etc.) within their scope and communicate to the group leader when additional assistance is needed
• •Must support training team members
• •Must interact with other departments to resolve issues
• •Must perform housekeeping and other job-related duties assigned by supervisor
• •Must frequently handle and ensure that cleanliness and orderliness standards are met throughout the plant
• •Must do the work him/herself whenever necessary
• •Must promote department cleanliness
• •Must keep all shop areas clean
• •Must keep parts put away in an orderly fashion
• •Must promote tool organization and workstation organization
• •Must provide platforms and raw material block-ups to the CNC machines operating spray equipment
• •Must maintain schedule and quality
• •Must apply fiberglass chop & barrier coats on sealed foam plugs
• •Must fabricate raw material blocks to drawings provided or verbal direction from the supervisor
• •Must fabricate plywood bases
• •Must manage platforms and cart inventory
• •Must layout, cut and bond foam to platforms and carts for both machines
• •Must construct wood boxed structures as filler for foam block-up
• •Must deck platforms and carts with plywood as substrate to bond foam blocks
• •Must strip platforms after mold production and prepare for reuse
• •Must ensure all operations are performed safely
• •Must maintain all areas and equipment clean neat and organized, at all times
• •Must conduct daily routine maintenance of equipment
• •Must store all materials safely at the end of the day
• •Must conduct operations using TDC mold fabrication approved processes (ISPC)
• •Must have safe operation of table saws, band saws, sanders, planers etc.
• •Must have Chop gun and barrier gun (Spraycore)
• •Must have Use of typical woodworking hand tools
• •Must have Understanding of adhesive systems and their use
• •Must have Reading fabrication drawings
• •Must have General knowledge and understanding of required power tools